Installation, debugging and after-sales service
Installation and debugging
Within three days of the machine tool arriving at the buyer's factory, the buyer shall notify the seller. Upon receiving the installation notice from the buyer, the seller will immediately send engineering technicians to the buyer's site to provide free installation, debugging, and personnel training for the complete system. Before installation and debugging, the buyer and company personnel will jointly unpack and check according to the contract quantity and packing list.
Acceptance
The precision indicators of the machine tool will be inspected according to the precision inspection table provided in the packing list, with inspection methods based on VDI (3441) standards. In case of disputes regarding the inspection results, a re-inspection will be conducted by the China Machine Tool Testing Center, during which the buyer shall seal and store the machine tool. The buyer's operation of the machine tool will be considered as acceptance.
Training
After the contract is signed, the user may send personnel to the seller's factory for a week of free on-site training before the machine tool arrives.
Warranty
From the date of acceptance, the machine tool is under a one-year free warranty. If the equipment cannot operate normally during the warranty period, the seller will send an engineer to the buyer's factory within 24 hours after receiving the buyer's notification. If the damage is caused by improper use, the cost of parts will be charged. After the warranty period, the machine tool will be covered for repairs.
Specification Table |
||||
| Specifications | ||||
| MZ-S650 | ||||
Processing Range |
Capacity |
|||
| Maximum Turning Diameter | Max.swing | mm(in) | 550 | |
| Turning Diameter on Slide | Swingovercrossslide | mm(in) | 260 | |
| Maximum Processing Diameter | Max.turningdiameter | mm(in) | 500 | |
| Maximum Processing Length | Max.turninglength | mm(in) | 600 | |
| Maximum Diameter of Bar Material | Bar capacity | mm(in) | 75(2") | |
Travel |
Travel |
|||
| X Axis | X axis | mm(in) | 260 | |
| Z Axis | Z axis | mm(in) | 650 | |
| Spindle | Spindle | |||
| Spindle Speed | Spindle speed range | rpm | 2500 | |
| Spindle Nose Type | Type of spindle nose | A2-8 | ||
| Through Spindle Hole Diameter | Through spindle hole diameter | mm(in) | 86 | |
| Front Bearing I.D./O.D. | Front bearing I.D./O.D. | mm(in) | 130/190(3.5" /5.5" ) | |
| Rear Bearing I.D./O.D. | Rear bearing I.D./O.D. | mm(in) | 110/170(3.5" /5.5") | |
| Spindle Motor Type | Spindle motor type | VEICHI | aP12/6000 | |
| Spindle Motor Power | Spindle motor power | KW(HP) | 15 | |
| Max. Spindle Torque | Max.spindle torque | Kgf.m | 130 | |
| Max. Torque Speed | Max.spindle speed torque | rpm | 1500 | |
Turret |
Turret |
|||
| Number of Tool Stations | Number of tool stations | 12 | ||
| Shank Height for Square Tool | Shank height for square tool | mm(in) | 25 | |
| Shank Diameter for Boring Bar | Shank diameter for boring bar | 32 | ||
| Turret Indexing Time (Adjacent Tool) sec | Turret indexing time(adjacent tool)sec | 0.25 | ||
| Turret Indexing Time (Adjacent Tool) sec sec |
Turret Indexing Time (180deg) sec | 1.0 | ||
Feed Rate |
Feedrate |
|||
| X Axis Rapid Traverse | X axis rapid traverse | m(ft)/m(in) | 15(49.2) | |
| Z Axis Rapid Traverse | Z axis rapid traverse | m(ft)/m(in) | 20(98.4) | |
| Feed per Revolution | Feed per revolution | mm/rev | 0.01-500 | |
| Jog Feedrate | Jog feedrate | mm(in)/min | 1260(49.6” ) | |
| Min. Spindle Indexing Increment | Min.spindle indexing increment | ±0.001 | ||
| Rate | ||||
Precision |
Accuracy |
||||
| Positioning X,Z | Positioning X,Z | VDI(3441) | mm | 0.015/1000;0.01/1000 | |
| Repeatability X,Z | Repeatability X,Z | VDI(3441) | mm | 0.01/1000;0.007/1000 | |
Bed & Slide |
Bed&Slide |
||||
| Overall Bed Guide Width | Overall bed guide width | mm(in) | 45 | ||
| X axis slide guide width | Cross slide guide width | mm(in) | 45 | ||
| Angle of bed | Angle of bed | deg | 30° | ||
Servo motor |
Feed motors |
||||
| X axis motor | X axis motor | α8/3000i/KW(HP) | 2.4(2.1) | ||
| X axis motor rated torque at stall Kgf-cm |
X axis motor rated torque at stall | 11.46NM | |||
| X axis thrust force | X axis thrust force | Kg-f | 920 | ||
| Z axis motor | Z axis motor | α8/3000i/KW(HP) | 2.4(2.1) | ||
| Z axis motor rated torque | Z axis motor rated torque | Kgf-cm | 11.46NM | ||
| Z axis thrust force | Z axis thrust force | Kg-f | 1500 | ||
Ball screws |
Ball screws |
||||
| X Axis | X axis dia.pitch | mm | 4010xP10 | ||
| Z Axis | Z axis dia.pitch | mm | 4012xP12 | ||
| Tailstock | Tailstock | ||||
| Tailstock movement type | Tailstock movement type | --- | Manual hydraulic | ||
| Tailstock movement | Tailstock movement | m(in) | --- | 550 | |
| Quill movement type | Quillmovementtype | --- | Hydraulic | ||
| Quill stroke | Quill stroke | mm(in) | --- | 100 | |
| Quill diameter | Quill diameter | mm(in) | --- | ψ75(3") | |
| Quill inside taper | Quill inside taper | M.T | --- | 5 | |
| Quill Max thrust | Quill Max thrust | Kg-f | --- | 400 | |
Hydraulic unit |
Hydraulic unit |
||||
| Pump motor | Pump motor | KW(HP) | 1.5 | ||
| Pump capacity | Pump capacity | 1/min | 30 | ||
| Pump pressure | Pump pressure | kg/cm | 70 | ||
| Tank capacity | Tank capacity | L | 50 | ||
| Coolant system | Coolant system | ||||
| Pump motor | Pump motor | KW(HP) | 0.37 | ||
| Pump performance | Pump capacity | 1/min | 25 | ||
| Pump pressure | Pump pressure | kg/cm | 1.6 | ||
| Tank capacity | Tank capacity | L | 100 | ||
Central lubrication |
Central lubrication |
||||
| Pump motor | Pump motor | W | 20 | ||
| Pump performance | Pump capacity | c.c./min | 180 | ||
| Pump pressure | Pump pressure | kg/cm | 12~15 | ||
| Tank capacity | Tankcapacity | L | 3 | ||
Other items |
Miscellaneous |
||||
| Power supply | Power supply | KVA | 18 | ||
| Mass of machine | Mass of machine | kg | 4500 | ||
| Machine dimensions(L) | Machine dimensions(L) | mm(in) | 2400 | ||
| Machine dimensions(W) | Machine dimensions(W) | mm(in) | 1750 | ||
| Machine dimensions(H) | Machine dimensions(H) | mm(in) | 1820 | ||
For more data, please click to download the preview on the right
Key Words
MZ-5065
Summary:
Contact Us
Classification:
We look forward to working with you, Jointly promote the development of China's machinery manufacturing and automation