Installation, debugging and after-sales service
Installation and debugging
Within three days of the machine tool arriving at the buyer's factory, the buyer shall notify the seller. Upon receiving the installation notice from the buyer, the seller will immediately send engineering technicians to the buyer's site to install, debug the entire system, and provide personnel training free of charge. Before installation and debugging, the buyer and company personnel will jointly unpack and check according to the contract quantity and packing list.
Acceptance
The precision indicators of the machine tool will be inspected according to the precision inspection table provided in the packing list, with the inspection method based on VDI (3441) standards. In case of disputes over the inspection results, a re-inspection will be conducted by the China Machine Tool Testing Center, during which the buyer shall seal and store the machine tool. The buyer's operation of the machine tool will be considered as acceptance.
Training
After the contract is signed, the user can send personnel to the seller's factory for a week of free on-site training before the machine tool arrives.
Warranty
From the date of acceptance, the machine tool is under a one-year free warranty. During the warranty period, if the equipment cannot operate normally, the seller will send an engineer to the buyer's factory within 24 hours of receiving the buyer's notification. If the damage is caused by improper use, the cost of parts will be charged. After the warranty period, the machine tool will be covered for repairs.
Specification Table |
||||
| Specifications | ||||
| MZ-S650 | ||||
Processing Range |
Capacity |
|||
| Maximum Turning Diameter | Max.swing | mm(in) | 550 | |
| Turning Diameter on Slide | Swingovercrossslide | mm(in) | 260 | |
| Maximum Processing Diameter | Max.turningdiameter | mm(in) | 500 | |
| Maximum Processing Length | Max.turninglength | mm(in) | 400 | |
| Maximum Diameter of Bar Material | Bar capacity | mm(in) | ψ52(2") | |
| Travel | Travel | |||
| X Axis | X axis | mm(in) | 260 | |
| Z Axis | Z axis | mm(in) | 450(17.7") | |
Spindle |
Spindle |
|||
| Spindle Speed | Spindle speed range | rpm | 3000 | |
| Spindle Nose Type | Type of spindle nose | A2-6 | ||
| Spindle Hole Diameter | Through spindle hole diameter | mm(in) | ψ62(2.4") | |
| Front Bearing I.D./O.D. | Front bearing I.D./O.D. | mm(in) | 110/170(3.5" /5.5") | |
| Rear Bearing I.D./O.D. | Rear bearing I.D./O.D. | mm(in) | 90/140(3.5" /5.5") | |
| Spindle Motor Type | Spindle motor type | VEICHI | aP12/6000 | |
| Spindle Motor Power | Spindle motor power | KW(HP) | 11 | |
| Max. Spindle Torque | Max.spindle torque | Kgf.m | 96 | |
| Max. Torque Speed | Max.spindle speed torque | rpm | 1500 | |
| Min. Spindle Indexing Increment | Min. spindle indexing increment | ±0.001 | ||
Tool Turret |
Turret |
|||
| Number of Tool Stations | Number of tool stations | 12 | ||
| Shank Height for Square Tool | Shank height for square tool | mm(in) | 25 | |
| Shank Diameter for Boring Bar | Shank diameter for boring bar | mm(in) | 32 | |
| Turret Indexing Time (Adjacent Tool) | Turret indexing time(adjacent tool)sec | sec | 0.25 | |
| Turret Indexing Time (Adjacent Tool) | Turret Indexing Time (180 Degrees) | sec | 1.0 | |
Feed Rate |
Feedrate |
|||
| X Axis Rapid Traverse | X axis rapid traverse | m(ft)/m(in) | 15(49.2) | |
| Z Axis Rapid Traverse | Z axis rapid traverse | m(ft)/m(in) | 20(98.4) | |
| Feed Per Revolution | Feed per revolution | mm/rev | 0.01-500 | |
| Jog Feed Rate | Jog feedrate | mm(in)/min | 1260(49.6") | |
Precision |
Accuracy |
||||
| Two-Axis Positioning Precision | Positioning X,Z | VDI(3441) | mm | 0.015/1000;0.01/1000 | |
| Two-Axis Repeatability Precision | Repeatability X,Z | VDI(3441) | mm | 0.01/1000;0.007/1000 | |
Bed and Slide |
Bed&Slide |
||||
| Z Axis Slide Width | Overall bed guide width | mm(in) | 45 | ||
| X-axis slide rail width | Cross slide guide width | mm(in) | 45 | ||
| Bed angle | Angle of bed | deg | 30° | ||
Servo motor |
Feed motors |
||||
| X-axis motor | X axis motor | α8/3000i/KW(HP) | 2.4 | ||
| X-axis motor torque | X axis motor rated torque at stall | Kgf-cm | 11.46NM | ||
| X-axis thrust | X axis thrust force | Kg-f | 920 | ||
| Z-axis motor | Z axis motor | α8/3000i/KW(HP) | 2.4 | ||
| Z-axis motor torque | Z axis motor rated torque | Kgf-cm | 11.46NM | ||
| Z-axis thrust | Z axis thrust force | Kg-f | 1500 | ||
Ball screws |
Ball screws |
||||
| X Axis | X axis dia.pitch | mm | 4010xP10 | ||
| Z Axis | Z axis dia.pitch | mm | 4012xP12 | ||
Tailstock |
Tailstock |
||||
| Tailstock movement type | Tailstock movement type | --- | Manual hydraulic | ||
| Tailstock movement | m(in) | Quill movement type | --- | 450 | |
| Hydraulic | Quillmovementtype | --- | Quill stroke | ||
| Quill stroke | Quill diameter | mm(in) | --- | 100 | |
| Quill diameter | ψ75(3") | mm(in) | --- | Quill inside taper | |
| Quill inside taper | Quill Max thrust | M.T | --- | 5 | |
| Quill Max thrust | Hydraulic unit | Kg-f | --- | 400 | |
Hydraulic unit |
Pump motor |
||||
| Pump motor | Pump capacity | KW(HP) | 1.5 | ||
| Pump capacity | Pump pressure | 1/min | 30 | ||
| Pump pressure | Tank capacity | kg/cm | 70 | ||
| Tank capacity | Coolant system | L | 50 | ||
Coolant system |
Pump power |
||||
| Pump performance | Pump capacity | KW(HP) | 0.37 | ||
| Pump pressure | Pump pressure | 1/min | 25 | ||
| Tank capacity | Tank capacity | kg/cm | 1.6 | ||
| Central lubrication | Coolant system | L | 100 | ||
Central lubrication |
Oil pump power |
||||
| Oil pump performance | Pump capacity | W | 20 | ||
| Oil pump pressure | Pump pressure | c.c./min | 180 | ||
| 12~15 | Tank capacity | kg/cm | Oil tank capacity | ||
| Other items | Coolant system | L | 3 | ||
Power supply |
Miscellaneous |
||||
| Power supply | Mass of machine | KVA | 15 | ||
| Mass of machine | Machine dimensions(L) | kg | 4200 | ||
| Machine dimensions(L) | Machine dimensions(W) | mm(in) | 2200 | ||
| Machine dimensions(W) | Machine dimensions(H) | mm(in) | 1750 | ||
| Machine dimensions(H) | For more data, please click to download the preview on the right | mm(in) | 1820 | ||
查看更多数据请到右侧点击下载预览
MZ-5045
Summary:
Contact Us
Classification:
We look forward to working with you, Jointly promote the development of China's machinery manufacturing and automation